AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
The speaker is too far from transmitter, move closer. Ensure the volume level of speakers is adjusted properly. You must then press the AUTO SCAN button on the speaker. Change the position of the channel selector on the transmitter. Press the AUTO SCAN button on the speakers or remoteĬontrol unit until the frequency of the transmitter matches. The volume of speaker is too low, adjust the volume The connected audio / video equipment is not playing. #Manual for centrios wireless speakers troubleshooting tv#Ensure the TV or audio component is ON. Speaker’s battery capacity is too low, replace with newīatteries or connect the AC adaptors to the speakers. Ensure the AC adaptor is fully inserted into the AC outletĪnd the power connection input on the transmitter. If there is no signal from the remote control unitįor 5 minutes, the speakers will automatically power off. Using the remote control unit during stand-by time. Minutes and the LED will change from blue to yellow. Use the remote control unit to turn off the speakers, the speakers will be at stand-by mode for 5 Press the POWER button to turn off the speaker and the blue POWER LED light will go off. Signal comes back, the transmitter will work again automatically.Ģ. There is no or weak operation input signal from audio source for 4 minutes.In other words, if the For protection of the transmitter and for power saving, the transmitter will cut off automatically if When transmitting / receiving over long distances, the signal from the system willġ. You can re-adjust the tuning controlīy moving it either to channel 1 or 2 of the transmitter, then pressing AUTO SCAN button for the best #Manual for centrios wireless speakers troubleshooting free#Transmitter, and then move the speakers to another free location. If you hear interference from other components, switch the channel control of the Ifĭisruption should occur (signal breaks up), press the speaker’s AUTO SCAN button to maximize You should now be able to move the speakers freely from room to room without disruption. Replace the cover to close the battery compartment. (not included) into the battery compartment with the correct polarity.Ģ. Remove the battery cover at the rear of the remote control unit and insert 2 “AAA” size batteries Turn bass/boost effect ON simply by pressing the button, and pressing it once againġ. The BOOST BASS button can be used to enhance the bass sound depending on your own music The other channel (there are two channels for this selection) on the transmitter,Īnd then press the “Auto Scan” button again.ĥ. Press the “AUTO SCAN” button for the best tuning reception.ī) Whenever you find a frequency jam, move your channel switch from one channel to A) Keep a distance from the speaker up to 7 meters apart from the transmitter, and then When the button is pressed, frequency tuning starts automatically and it stops when a signal isĭetected. Push the “AUTO SCAN” button on the speaker or Remote Control to get the best tuning reception. Press the + / - (volume level) button on the speaker and adjust the volumeĤ. Select the channel 1 or 2 of the transmitter for best performance in your location.ģ. As soonĪs the transmitter receives the audio signal,Ģ. To which the transmitter is connected with. Turn on the audio source (TV or audio component) Of each speaker, then plug it to the wall AC outlet. Polarity at the rear of the speaker or connect the 12V power adaptor to the DC input jack on the rear Insert 6 ‘AA’ size ALKALINE batteries (not included) into the battery compartment with correct Make sure the adaptor is plugged in properly. Plug the adapter into the AC source and theīlue POWER LED will illuminate. TV, Monitor, VCR, Radio, CD/MP3/VCD/DVD player or to a headphone/earphone jack with the The rear of the transmitter has one audio cord that can be connected to audio output jack of a Insert the antenna into the antenna wire.Ĭonnect the supplied AC power adaptor to an electrical wall outlet. Virtually interference free stereo quality.Ģ wireless panel speakers with detachable speaker grills. No line of sight limitation for the speakers. Infrared remote control unit for your convenience (must be in line with transmitter). RF technology lets you roam freely throughout your house. Phase Lock Loop (PLL) technology on the transmitter. System enables you to enjoy thrilling, lifelike sound stereo in minutes.ĩ00 MHz RF technology panel-like speaker system. WithoutĬomplicated wiring and installation with your Audio/Video equipments and rear channel amplifier, the System to any audio source such as Radio, TV, VCR, Hi-Fi and CD/MP3/VCD/DVD player. You to enjoy music and TV sound anywhere inside or outside your home. These 900 MHz stereo wireless speaker system uses the latest wireless technology that enables
0 Comments
Read More
Leave a Reply. |